Posts Tagged ‘FRP wall panel’

FRP wall panels are great for protecting walls in mud rooms, shops, bathrooms – basically anywhere you need easy-to-clean wall protection. However, it’s not just as simple as nailing in a few sheets of panel, you will need to plan ahead for your project.

We recommend you get some graph paper first and get some measuring tape. Go to the room you’re going to put the sheets into and measure the width of all the walls. Make notes of how many inside or outside corners you have in the room at this stage. Now note that the FRP wall panel sheets are all going to be 4′ x 8′ or 4′ x 12′ in size. How are you going to orientate them? If you need only coverage right near the floor, you could potentially put the sheets sideways to save on the total the amount of sheets you require. Sketch that onto your graphic paper because you will need to know how many sheets to put on a given wall. The reason for this is that you require dividers (known as ‘j-trims’) for the spaces between the panels on a given length of wall.

All j-trims, inside and outside corners come in 10′ lengths. You need to consider that you may need extra of those to cut-to-size to fit into your project. Lastly, you need to consider FRP adhesive. Many jobs are not actually done by nailing in FRP panel to the wall. Instead a special FRP adhesive is used that comes in 4 gallon buckets. Each bucket covers 200 square feet of surface area. Based off of 4′ x 8′ panels (32 square feet) or 4′ x 10′ panels (40 square feet) add up the total square footage of your panels divided by 200 and then round up…That’s how many buckets of FRP adhesive you require. Also factor in you will want to have a trowel to spread the adhesive onto the panels.

At this point you should be ready to quote! You now know 1.) how many panels you need 2.) how many j-trims/inside/outside corners you need along with 3.) required adhesive. You’re set to purchase the material and get started!

 

FRP wall panels are a great product for the DIY community. The panels are strong, long-lasting, grime and vandalism resistant. Excellent for applications such as bathrooms, garages, “mud rooms”, or areas animals are kept. FRP wall panels have a relatively economical cost compared to industrial FRP panels, are widely available, and easy to install. As with any project, preparation is key to saving money and prevent disappointment with the final result.

To start the first thing you want to do is draw a quick sketch of the area to be covered. Mark each wall with how many feet it is in length. FRP wall panels come in 4′ x 8′ and 4′ x 10′ panels and the next thing you need to do is figure out how you will orientate the panels. Start at the floor – will they be arranged to provide more height by being set side-to-side by their width? or by their length to provide 4′ high coverage? In many applications, the panels can be placed on their side to cover more area and reduce costs. You should now be able to figure out how many panels you need.

Next, figure out how much FRP adhesive you need. The adhesive comes in 4 gallon buckets and covers 200 square feet. simply add up the total area of the panels you need and divide by 200. For example, if your project requires 12 4′ x 10′ panels that is 480 square feet / 200 = 2.4 or 3 buckets of adhesive will be needed. It’s always good to have some extra so never round down!

Following this step you need to figure out how many inside corners/outside corners/j-trims you need. Inside corners and outside corners are PVC plastic dividers for FRP wall panel that are purchased alongside the panels. This is pretty simple as you just count how many corners you have. The trims and corners all come in 10′ lengths. The j-trims require a bit more thought. These are also PVC but are used to join two panels where there are no corners. You need to be able to sketch or visualize where your panels will buttress up against each other along the stretches of wall and be able to count up what you need.

And that’s pretty much it! At this point you should have a clear idea of the scope of your project and all the requirements for your FRP panels and how many accessories you need. The next step is to simply contact your plastics distributor and request a quotation. Please give clear and specific requests including relevant quantities for all required components. That will ensure a quick and accurate quotation.